Material Safety Data Sheet - Instant Bonder IB-SI article

IDENTITY: ETHYL CYANOACRYLATE IB-SI

I. MANUFACTURER: SAF-T-LOK INTERNATIONAL CORP.
300 EISENHOWER LANE NORTH
LOMBARD, ILLINOIS, USA 60148
EMERGENCY TELEPHONE: 800-222-2087

DATE PREPARED: NOVEMBER 01, 2006

II. HAZARDOUS COMPONENTS: NONE

ALL COMPONENTS OF THIS PRODUCT ARE LISTED ON THE TOXIC SUBSTANCE CONTROL ACT (TSCA) INVENTORY OF CHEMICAL SUBSTANCES MAINTAINED BY THE U.S. ENVIRONMENTAL PROTECTION AGENCY.

III. PHYSICAL / CHEMICAL CHARACTERISTICS:
Boiling Point: >278
°
F                                         Specific Gravity: 1.10
Vapor Pressure (mm Hg) <1 @ 30 
°
F               Melting Point:` N/A
Vapor Density (Air= 1) 4.3                                 Evaporation Rate: N/A
Solubility in Water: Polymerized by water.       Appearance /Odor: Transparent liquid with ester-like odor.

IV. FIRE AND EXPLOSION HAZARD DATA:
Flash Point (Method Used): T.C.C. 176
°
F.      Flammable Limits: N/A
Extinguishing Media: CO2, Foam, Dry Chemicals
Special Fire Fighting Procedures: Fire can produce dense smoke containing hazardous products of combustion (see Section V), which may be a hazard to health. Self contained breathing apparatus and procedures for fighting chemical fires should be employed.

V. REACTIVITY DATA:
Unstable. Avoid high temperatures. high humidity, and materials such as water, alcohols, amines and alkalics which may cause polymerization which may be exothermic.

VI. HEALTH HAZARD DATA:
Possible routes of entry include skin and ingestion.

This product is not included on any list for carcinogenicity.

WARNING:    Eye irritant. Bonds skin in seconds. Contains cyanoacrylate ester. This adhesive gives a virtually immediate, strong bond: apply only to surfaces to be bonded. Do not get adhesive on your skin or other parts of your body, or that of others. In case of body contact, flush with water. Seek medical attention for any eye or internal contact.

LIQUID EFFECTS:

EYE CONTACT:   Cyanoacrylate adhesives are eye irritants and tissue bonders. Therefore, care, including the use of goggles, should be taken to prevent eye contact. In the event of eye contact, the eyes should be copiously flushed with water and medical aid sought immediately. If eyelids are bonded closed, only a qualified physical should attempt to separate them. In case of bonding corneal surface, forced separation is not recommended. Allow the eye to remain closed and the bond to separate naturally, which generally will occur within a few days.

SKIN CONTACT:   Cyanoacrylate adhesives, while relatively non-toxic, are mild irritants to the skin. The Acute Dermal LD50 is >2000 mg/kg. However, strong bonds will quickly form between adjacent skin surfaces, e.g. fingers. These may be separated relatively easily by soaking the bonded area in warm, soapy water for several minutes, or soaking in SAF-T-LOK Debond, and then gently peeling the bond. Alternatively, a dull instrument such as a thin wire or a table knife can be forced through the bond. With appropriate caution, solvents such as acetone or nail polish remover can be used effectively.

When skin contact is over a large area, the area should be flushed with large amounts of water. A soaking wet cloth can be used to wipe off excess adhesive. If the adhesive has soaked through clothing, flush the involved area with water. If the cloth has bonded to the skin, the removal of the bonded clothing without these precautions might result in skin damage. Cured adhesive will flake from the skin within a day or so or can be removed by treatment or by soaking with hot, soapy water.

ORAL CONTACT:    Cyanoacrylates are relatively non-toxic materials (Acute Oral LD50 >5000 mg/kg.) However,, rapid polymerization (hardening) of the adhesive will take place in contact with the surfaces of the mouth. The mouth should be flushed copiously with water and medical aid should be sought immediately. Lips, if bonded, can be gently peeled apart, preferably with the aid of hot water or solvent.

VAPOR EFFECTS:

EYES:   Alkyl cyanoacrylate vapors are lachrymatory (tear producing) and can cause eye irritation and tearing in poorly ventilated areas.

MUCOUS MEMBRANES   : Mucous surfaces can become irritated by prolonged exposure to cyanoacrylate vapors in poorly ventilated areas. Vapor irritation to the eyes and mucous membranes will be most noticeable under conditions of low relative humidity.

VAPOR CONTROL RECOMMENDATIONS:

* Use adequate ventilation. Remove adhesive vapors with suitable exhaust ducting. Since cyanoacrylate vapors are heavier than air, place exhaust intake below work area. Activated charcoal filters using an acidic charcoal have been found effective in removing vapors from effluent air.

* Avoid use of excess adhesive. Excess adhesive outside of bond area will increase level of vapors.

* Assemble parts as quickly as possible. Long open times will increase level of vapors.

VII. PRECAUTIONS FOR SAFE HANDLING AND USE:
Health hazard rating is 2,  Slightly hazardous. Fire hazard is 2, Flash point above 100 
° F not exceeding 200. Reactivity rating is 1, Unstable if heated.

Provide adequate ventilation in area of usage. When possible this should be achieved by the use of local exhaust ventilation and good general ventilation. Vapors are heavier than air, therefore, downward ventilation should be used. When handling cyanoacrylate adhesives, goggles or safety glasses should always be worn. Polyethylene gloves should be used to protect the hands. CAUTION: Do not use rubber or cloth gloves. Rubber gloves will bond when brought in contact with the adhesive and porous cotton gloves will absorb the adhesive and bond the gloves to the skin.

Store in original container below 40° F for prolonged shelf life.

In the event of small spills, material may be wiped up with a soaking wet cloth and the area cleaned with solvent. When large quantities of cyanoacrylate adhesive are accidentally spilled, the area should be flooded with water which will cause the liquid cyanoacrylate to cure. The cured material can then be scraped from the surface. It may then be incinerated observing all State, Federal and local anti-pollution and waste disposal regulations.

VIII. CONTROL MEASURES:
Transport: This product is not regulated for shipping purposes.

Other: Respiratory protection is not normally necessary unless product is used in enclosed area of poor ventilation or individual has a history of chronic respiratory disease. Local exhaust is recommended. Protective gloves are recommended during use (See section VII above). Always wash hands thoroughly after use.

The information on this data sheet represents our current data and best opinion as to the proper use in handling of this product under normal conditions. Any use of the product which is not in conformance with this data sheet or which involves using the product in combination with any other product or any other process is the responsibility of the user.




MSDS: Material Safety Data Sheets

Material Safety Data Sheet - Threadlocker T22 article
Material Safety Data Sheet - Threadlocker T41 article
Material Safety Data Sheet - Threadlocker T42 article
Material Safety Data Sheet - Threadlocker T62 article
Material Safety Data Sheet - Threadlocker T70 article
Material Safety Data Sheet - Threadlocker T72 article
Material Safety Data Sheet - Threadlocker T77 article
Material Safety Data Sheet - Retainer R01 article
Material Safety Data Sheet - Retainer R20 article
Material Safety Data Sheet - Retainer R35 article
Material Safety Data Sheet - Retainer R41 article
Material Safety Data Sheet - Retainer R42 article
Material Safety Data Sheet - Retainer R80 article
Material Safety Data Sheet - Retainer R90 article
Material Safety Data Sheet - Thread Sealant S90 article
Material Safety Data Sheet - Thread Sealant PS article
Material Safety Data Sheet - Thread Sealant HS article
Material Safety Data Sheet - Thread Sealant RS article
Material Safety Data Sheet - Thread Sealant CP article
Material Safety Data Sheet - Pipe Sealant TPS article
Material Safety Data Sheet - Pipe Sealant I-TPS article
Material Safety Data Sheet - Pipe Sealant FD-TPS article
Material Safety Data Sheet - Pipe Sealant SS article
Material Safety Data Sheet - Flange Sealant PFS-Yellow article
Material Safety Data Sheet - Flange Sealant PFS-Red article
Material Safety Data Sheet - Flange Sealant PFS-Blue article
Material Safety Data Sheet - RTV Silicone 732 Clear article
Material Safety Data Sheet - RTV Silicone 732 White article
Material Safety Data Sheet - RTV Silicone 732 Black article
Material Safety Data Sheet - RTV Silicone 732 Aluminum article
Material Safety Data Sheet - RTV Silicone 732 Red article
Material Safety Data Sheet - RTV Silicone 732 NC Clear article
Material Safety Data Sheet - Instant Bonder IB-5 article
Material Safety Data Sheet - Instant Bonder IB-45 article
Material Safety Data Sheet - Instant Bonder IB-100 article
Material Safety Data Sheet - Instant Bonder IB-1500 article
Material Safety Data Sheet - Instant Bonder IB-HT article
Material Safety Data Sheet - Instant Bonder IB-GEL article
Material Safety Data Sheet - Instant Bonder IB-NF article
Material Safety Data Sheet - Instant Bonder IB-B article
Material Safety Data Sheet - Structural Adhesive SA-5 article
Material Safety Data Sheet - Structural Adhesive SA-24 article
Material Safety Data Sheet - Structural Adhesive TRI-CURE article
Material Safety Data Sheet - Structural Adhesive TRI-CURE II article
Material Safety Data Sheet - Chemical Primer T article
Material Safety Data Sheet - Chemical Primer N article
Material Safety Data Sheet - Solventless Primer T article
Material Safety Data Sheet - Solventless Primer N article
Material Safety Data Sheet - Chemical Accelerator article
Material Safety Data Sheet - Chemical Debond article
Material Safety Data Sheet - Chemical Activator article
Material Safety Data Sheet - Regular Anti-Seize article
Material Safety Data Sheet - Copper Anti-Seize article
Material Safety Data Sheet - Nickel Anti-Seize article
Material Safety Data Sheet - Nickel Premium Anti-Seize article
Material Safety Data Sheet - Food/Drug Anti-Seize article
Material Safety Data Sheet - Moly Grade Anti-Seize article
Material Safety Data Sheet - Moly 50 Anti-Seize article
Material Safety Data Sheet - Nuclear Nickel Anti-Seize article
Material Safety Data Sheet - Nuclear Copper Anti-Seize article
Material Safety Data Sheet - G/P Aircraft Grade Anti-Seize article
Material Safety Data Sheet - Z/P Aircraft Grade Anti-Seize article
Material Safety Data Sheet - High-Temp Bearing Lubricant article
Material Safety Data Sheet - Bearing Lubricant Extended Life article
Material Safety Data Sheet - EP Bearing Lubricant article
Material Safety Data Sheet - Food/Machinery Lubricant article
Material Safety Data Sheet - General Purpose Silicone Lube article
Material Safety Data Sheet - Di- Electric Silicone Compound article
Material Safety Data Sheet - Flange-Seal article
Material Safety Data Sheet - Torque-Seal article
Material Safety Data Sheet - Pipe-Seal article
Material Safety Data Sheet - Fine Pipe-Seal article
Material Safety Data Sheet - Belt-Dress (Aerosol) article
Material Safety Data Sheet - Contact-Clean (Aerosol) article
Material Safety Data Sheet - Gasket-Off (Aerosol) article
Material Safety Data Sheet - Dry-Moly (Aerosol) article
Material Safety Data Sheet - Silicone-Lube (Aerosol) article
Material Safety Data Sheet - T-Gel Lube (Aerosol) article